SCATTERING OF CIRCULAR CAVITY IN RIGHT-ANGLE PLANAR SPACE TO STEADY SH-WAVE

Complex function method and multi-polar coordinate transformation technology are used here to study scattering of circular cavity in right-angle planar space to SH-wave with out-of-plane loading on the horizontal straight boundary. At first, Green function of right-angle planar space which has no circular cavity is constructed; then the scattering solution which satisfies the free stress conditions of the two right-angle boundaries with the circular cavity existing in the space is formulated. Therefore, the total displacement field can be constructed using overlapping principle. An infinite algebraic equations of unknown coefficients existing in the scattering solution field can be gained using multi-polar coordinate and the free stress condition at the boundary of the circular cavity. It can be solved by using limit items in the infinite series which can give a high computation precision. An example is given to illustrate the variations of the tangential stress at the boundary of the circular cavity due to different dimensionless wave numbers, the location of the circular cavity, the loading center and the distributing range of the out-of-plane loading. The results show the efficiency and effectiveness of the method introduced here.     

Residual Stress Determination Using Hole Drilling and 3D Image Correlation

In recent years, the hole drilling method for determining residual stresses has been implemented with optical methods such as holographic interferometry and ESPI to overcome certain limitations of the strain rosette version of hole drilling. Although offering advantages, the interferometric methods require vibration isolation, a significant drawback to their use outside of the laboratory. In this study, a 3D image correlation approach was used to measure micron-sized surface displacements caused by the localized stress relief associated with hole drilling. Residual stresses were then found from the displacements using non-dimensional relations previously derived by finite element analysis. A major advantage of image correlation is that it does not require interferometric vibration isolation. Experiments were performed to check the ability of this new approach for uniaxial and equi-biaxial states of stress. Stresses determined by the approach were in good agreement with computed values and those determined by hole drilling using holographic interferometry.     

Two theorems on the steady-state conduction in anisotropic body

In this paper, steady-state plane conduction problems are considered. Two theorems are proven on the conductance of non-homogeneous and anisotropic plane conductors. Here, the conductor is a two-dimensional bounded plane domain with a conducting matter having two seperated boundary terminals and two seperated insulated boundary segments. Known theorems referring to homogeneous and isotropic conductors have been extended to non-homogeneous and anisotropic ones. The results of the paper can be directly used in following fields: heat flow, diffusion, irrotational hydraulic flow, flow of electrical current and anti-plane shear deformation. Application of formulae derived is illustrated in the examples of heat flow and anti-plane elastic shear deformation.     

Deformation and failure mechanism in AISI 4340 steel under ballistic impact

Deformation and failure mechanism in quench-hardened AISI 4340 steel under ballistic impact is investigated. The influence of microstructure on damage evolution is also evaluated. Strain localization and shear failure along adiabatic shear bands are the dominant deformation and failure mechanisms. The time and critical strain for the commencement of strain localization is influenced by strain rate and microstructure. The microstructure of the steel sample also influenced the type of adiabatic shear bands formed during impact. Failure mechanism involves nucleation of micro-voids, which clusters to form bigger pores. Extremely fine micro-cracks are initiated adjacent to the pores and in shear flow direction along the shear bands. These micro-cracks become interconnected and grow to macro-cracks, which cause fracture of some of the investigated cylindrical steel samples under impact. The susceptibility of the adiabatic shear bands to cracking increases with decreasing tempering temperature of the steel.     

一种确定均匀动脉壁面切应力的非线性方法

从Ling和Atabek提出的``局部流'理论出发，提出一种利用测量血液黏度、管轴上 的血流速度、压力和管径波形计算均匀动脉管壁切应力的非线性方法. 将这种方法与柳兆荣 等提出的利用测量血液黏度、管轴上的血流速度和平均管径计算切应力的线性方法比较，结 果表明，当管壁脉动幅度较小时，两种方法计算的压力梯度、流速剖面和管壁切应力差别较 小；而当管壁脉动幅度增大时，两种方法计算的压力梯度、流速剖面和管壁切应力差别增大. 对于小幅脉动均匀动脉，用线性方法计算管壁切应力有较高的精度；而对于大变形 均匀动脉，则需要考虑非线性因素对管壁切应力的影响. 由于作为输入量的血液黏度、轴心 血流速度、压力波形和管径波形可在活体上通过无损伤或微损伤的检测方法得到， 所提出的计算切应力的方法为在体或离体研究切应力与动脉重建的关系提供了方法学基础.     

Rheological aspects of dense lignite–water suspensions; structure development on consecutive flow loops

Aspects of dense lignite–water slurries (LWS) rheology were investigated using controlled stress and controlled strain rheometers with parallel disks and Couette geometries. During the preparation of the slurries, the achieved solids volume fractions were up to 0.425 and the particle size distributions were polydispersed with sizes up to 300 μm. In the ascending parts of consecutive flow loops, a slope transition of the flow curve was observed and studied in relation to the solids volume fraction. The obtained results with the different geometries and rheometers were qualitatively the same. By following the model proposed by Cheng (Rheol Acta 42:372–382, 2003) for thixotropic fluids, and taking into account the yield stress appearance, a suitable correlation for LWS is proposed, which is consistent with the experimental flow curves.     

SHPB试验中粘弹性材料的应力均匀性分析

采用特征线解法，对满足ZWT方程的粘弹性材料在高应变率SHPB试验中的应力均匀性进行了数值研究。着重分析了不同的材料本构粘性(松弛时间)、瞬态波阻抗比和入射波升时对于试样中应力均匀性、应变均匀性和平均应变率等的影响。为今后动态试验的试样设计提供了一定的理论依据。     

具损伤压电智能层合板的动力分析

基于应变能等效原理、高阶剪切变形理论和Hamilton变分原理,考虑复合材料铺设层内的损伤效应,建立了具损伤压电智能层合板的运动控制方程,并运用Galerkin方法进行求解.数值算例中,讨论了损伤效应、厚跨比及压电层厚度与层合板总厚度之比对四边简支压电智能层合板自由振动频率的影响和外部控制电压对其动力响应的影响.     

Trapped particle detection in bonded semiconductors using gray-field photoelastic imaging

In this paper we present inspection results from several bonded wafer systems using a newly developed infrared gray-field polariscope (IR-GFP). This device measures the residual stress-fields associated with defects trapped at the bonded interface to enable the detection of subwavelength defects. Results from IR-GFP imaging are contrasted with conventional infrared transmission (IRT) imaging of the same samples, showing marked improvements in defect detection as well as the ability to quantify the residual stress fields. This inspection method reveals that interfaces deemed defect-free using IRT imaging may be, in fact, teeming with defects.     

利用无网格方法分析斜拉破坏钢筋混凝土梁

从传统的混凝土分离裂缝模型和弥散裂缝模型出发，使用不同的模型模拟不同发展阶段的混凝土裂缝，并利用无网格方法可以灵活布置节点和边界的优点，使分离裂缝模型的使用得到很大的简化。通过在宏观裂缝表面布置基于试验结果的混凝土与混凝土界面单元，正确地模拟了裂缝表面抗剪能力的变化。算例表明，使用本文方法可以准确模拟斜拉破坏混凝土梁的破坏过程，且精度和数值稳定性要高于传统的有限元弥散裂缝方法。